Skip to content
RecordPure logo — studio microphone icon with the RecordPure wordmark
  • Home
  • About UsExpand
    • Contact Us
  • Studio Microphones
  • Audio Interfaces
  • MIDI Controllers
  • Acoustic Treatment
  • Free Tools
RecordPure logo — studio microphone icon with the RecordPure wordmark
Free calculator

Headphone Drive Check: Will My Interface Power These?

Estimate whether an audio interface can drive your headphones: power in mW, maximum SPL and margin to your own target, with every step shown.

  • Free
  • No sign-up
  • Runs in your browser
Estimates only · data checked October 2026 · About this data

This tool performs electrical arithmetic only. Its output is an estimate, not a compatibility verdict, and it provides no hearing-safety or listening-level guidance. Always check the headphone and interface manufacturers' own documentation for specifications and usage information.

Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.

Quick answer

Whether your audio interface can drive studio headphones, over-ear or in-ear, comes down to three published specs: headphone sensitivity, headphone impedance and the interface’s headphone output voltage. Enter them below to estimate the power and maximum SPL, with every step shown. The result is an estimate, not a compatibility verdict.

How to use the Headphone Drive Check

  1. Open the headphone manufacturer’s product page or manual and find the sensitivity figure. Type the number into Sensitivity.
  2. Set Sensitivity unit to the unit printed next to that figure: dB SPL/mW or dB SPL/V. The two are not interchangeable, so check before you pick.
  3. Type the rated impedance in ohms from the same spec sheet into Impedance (Ω).
  4. Open the interface’s spec sheet or manual and find the maximum headphone-output level. The tool needs it in Vrms. If the manufacturer quotes it another way, convert it first; the tool does not guess.
  5. Optionally, type your own Target SPL. The field is blank on purpose: there is no default. Leave it blank to see only the power and the estimated SPL.
  6. Read the result. It lists the power into the headphone, the estimated maximum SPL, the margin against your target (if you entered one) and each calculation with your numbers substituted.

You can use either a dot or a comma as the decimal separator. Results update as you type, and changing the sensitivity unit clears the previous result before recalculating.

How the maths works

The tool runs two well-known formulas. First, the electrical power delivered to the headphone follows from P = V² ÷ R. With the voltage in Vrms and the impedance Z in ohms, the power in milliwatts is:

P (mW) = V² ÷ Z × 1000

Second, decibels describe power ratios on a logarithmic scale: a power level in dB is 10 × log10(P ÷ P0). If sensitivity is quoted in dB SPL/mW, it is the level at 1 mW, so the estimated maximum level is:

SPL = S (dB SPL/mW) + 10 × log10(P in mW)

If sensitivity is quoted in dB SPL/V, it is the level at 1 Vrms, and the voltage version of the same physics applies:

SPL = S (dB SPL/V) + 20 × log10(V)

Finally, the margin is the estimated SPL minus your own target. The verdict depends only on the sign of the margin. At zero or above, the result says: “On these numbers, the estimate reaches your target.” Below zero, it says how many dB the estimate falls short, and notes that a separate headphone amplifier is one option to look into. There are no other bands or labels.

SensitivityImpedanceOutputPowerEstimated max SPL
100 dB SPL/mW32 Ω1 Vrms1² ÷ 32 × 1000 = 31.25 mW100 + 10 × log10(31.25) ≈ 114.95 dB SPL
100 dB SPL/mW250 Ω1 Vrms1² ÷ 250 × 1000 = 4 mW100 + 10 × log10(4) ≈ 106.02 dB SPL
114.95 dB SPL/V32 Ω1 Vrms31.25 mW114.95 + 20 × log10(1) = 114.95 dB SPL
Arithmetic illustration, round numbers, not a real product. The third row cross-checks the dB/V path: 100 dB SPL/mW at 32 Ω is the same headphone as 114.95 dB SPL/V.

The first two rows show why impedance matters with a fixed output voltage: the same 1 Vrms pushes 31.25 mW into 32 Ω but only 4 mW into 250 Ω, a difference of about 8.9 dB for the same sensitivity in dB SPL/mW.

What this estimate can’t tell you

The result is labelled “estimated maximum SPL (sine-wave equivalent at the stated output voltage)” because the arithmetic leaves out several real-world factors:

  • the interface’s output impedance;
  • distortion and clipping near the interface’s maximum output;
  • frequency-dependent impedance (the rated figure is a single number);
  • the fit and seal of the headphone on your head or in your ear;
  • the difference between a steady sine-wave level and the dynamics of real music.

For those reasons, the tool never says that a headphone and interface pair is compatible, and a positive margin is not a promise of anything beyond the arithmetic. The tool also gives no default or recommended listening level and no hearing guidance.

Over-ear vs in-ear studio headphones: where to find the specs

The same check works for over-ear studio headphones and for in-ear monitors, because manufacturers of both publish sensitivity and impedance. Look in the specifications or technical data section of the product page, or in the manual. Sensitivity is usually measured at 1 kHz and is quoted either in dB SPL/mW or in dB SPL/V, so copy the unit along with the number. For context, the Wikipedia article on headphones notes that values between 80 and 125 dB/mW are common.

For the interface side, look for the headphone output’s maximum level. Some manufacturers also state the load it was measured into; if the stated load differs from your headphone’s impedance, treat the result as even more approximate. If you only have a sensitivity in one unit and want the other, use dB SPL/V = dB SPL/mW − 10 × log10(Z ÷ 1000).

Methodology & sources

Derivation. Power into the headphone is P = V² ÷ Z, multiplied by 1000 to give milliwatts. A dB SPL/mW sensitivity is the level at 1 mW, so each tenfold increase in power adds 10 dB: SPL = S + 10 × log10(P). A dB SPL/V sensitivity is the level at 1 Vrms; since power scales with V², 10 × log10(V²) = 20 × log10(V), giving SPL = S + 20 × log10(V). At 1 V the power in mW is 1000 ÷ Z, which is why the two units differ by 10 × log10(Z ÷ 1000).

Input validation. Sensitivity, impedance and output voltage are required and must be numbers greater than zero; empty, non-numeric, zero and negative entries show a message and no result, so the tool never takes the logarithm of zero or a negative number. The target is optional and must be above zero if entered; with no target, the tool shows power and SPL but no verdict. Soft warnings appear, without blocking the calculation, when sensitivity is outside 50–150, impedance is outside 1–2,000 Ω or output voltage is above 20 Vrms. These bounds are input sanity checks chosen for this tool, not claims about real products. Results too large or too small to display show a plain message instead.

  • Wikipedia: Electric power — the relation P = V²/R.
  • Wikipedia: Decibel — power level in dB = 10 × log10(P/P0).
  • Wikipedia: Headphones (Sensitivity section) — dB SPL/mW and dB SPL/V units, measurement at 1 kHz, the conversion between them and SPL = S + 20 × log10(V).
  • Your own headphone and interface manufacturers’ documents — the values you type in. The tool contains no product database and republishes no manufacturer tables.

This tool performs electrical arithmetic only. Its output is an estimate, not a compatibility verdict, and it provides no hearing-safety or listening-level guidance. Always check the headphone and interface manufacturers’ own documentation for specifications and usage information.

Last updated: October 2026

FAQ

What does 3 dB more mean in power terms?

It means about double the power, because 10 × log10(2) ≈ 3.01 dB. On the dB/V side, doubling the output voltage adds about 6.02 dB, because 20 × log10(2) ≈ 6.02.

Where do I find headphone sensitivity and impedance?

In the specifications section of the headphone manufacturer’s product page or manual. Sensitivity is quoted either in dB SPL/mW or in dB SPL/V, usually measured at 1 kHz, so note which unit is printed before you pick it in the tool.

How do I convert dB SPL/mW to dB SPL/V?

Use dB SPL/V = dB SPL/mW − 10 × log10(Z ÷ 1000), with Z in ohms. For example, 100 dB SPL/mW at 32 Ω works out to about 114.95 dB SPL/V (arithmetic illustration with round numbers, not a real product).

Does a positive margin mean my headphones and interface are compatible?

No. The result is an electrical estimate that ignores the interface’s output impedance, distortion and clipping, frequency-dependent impedance, fit and seal, and music dynamics, so it is not a compatibility verdict.

Why is there no default target SPL?

The tool gives no recommended or default listening level and no hearing guidance. You type your own target, and the tool only compares it with the estimate.

Related guides

  • Home Studio Layout Ideas for Small Rooms, Bedrooms and Closets
  • Home Studio Maintenance Checklist: Weekly, Monthly and Yearly Tasks
  • How Many Bass Traps Do I Need for a Small Home Studio?
  • How to Acoustically Treat a Room for Recording on a Home-Studio Budget
  • Types of Audio Connectors: A Visual Guide for Home Studios
  • How to Organize Cables in a Home Studio: Labels, Trays and Noise-Free Runs

More free tools

Audio Interface Buffer Size & Latency Calculator

Convert audio interface buffer size and sample rate to milliseconds, estimate round-trip delay with your own overhead, and view a latency chart.

Home Studio Room Calculator: Acoustic Treatment & Monitor Placement

Enter room size and finishes to get room modes, RT60 per octave, a panel count, monitor triangle, SBIR null and first-reflection points.

Recording Software Finder: Free & Paid DAWs and Recording Apps

Filter 23 verified recording apps and DAWs by price, license, platform, use case and feature, plus free DAWs bundled with interfaces.

See all free tools (4) →

  • Home
  • About Us
  • Contact Us
  • HTML SITEMAP
  • Privacy Policy
  • Terms of Service
  • Affiliate Disclaimer
  • How We Research

Please keep in mind that we may receive commissions when you click our links and make purchases. However, this does not sway our reviews and comparisons. We try our best to keep things unbiased, in order to help you make the best choice. As Amazon Associate, we earn from qualifying purchases.

© 2026 RecordPure | All Rights Reserved.

Scroll to top
  • Home
  • About Us
    • Contact Us
  • Studio Microphones
  • Audio Interfaces
  • MIDI Controllers
  • Acoustic Treatment
  • Free Tools
Search