Home Studio Room Calculator: Acoustic Treatment & Monitor Placement
Enter room size and finishes to get room modes, RT60 per octave, a panel count, monitor triangle, SBIR null and first-reflection points.
- Free
- No sign-up
- Runs in your browser
Estimates only · data checked October 2026 · About this data
Results are estimates from textbook formulas and generic published absorption data for an empty rectangular room. Real rooms, furniture, mounting and specific products differ, so verify with a measurement microphone before and after treatment.
Your entries and saved results stay in this browser. No account, no tool cookies, nothing you enter is sent to a server.
Quick answer
A room acoustic treatment calculator estimates how long your room rings (RT60), which bass frequencies build up, and how many absorber panels bring reverberation toward a published target. This one also plans your monitors: triangle spacing, toe-in, wall distance, and the points on the walls and ceiling where the first reflections land.
How to use the room acoustic treatment calculator
- Pick metric or imperial units, then enter the room length (from the wall behind your monitors to the back wall), width and ceiling height.
- Choose the finish closest to your walls, floor and ceiling. Each option shows which published table its absorption values come from.
- Choose a panel material and enter the face area of one panel (width × height). Leave the area empty if you only want RT60, modes and placement.
- If panels are already up, enter how many. The panel face area is then required.
- Enter the distance from the front of your monitors to the wall behind them, then press Calculate.
The results show:
- an estimated panel count;
- RT60 per octave band before and after treatment;
- the first four axial modes for each dimension;
- the speaker-boundary cancellation frequency;
- a top-down plan with monitors, listening spot, reflection panels and corner bass traps.
If an input is missing or the layout is impossible, the result box tells you which value to change.
The formulas behind the numbers
Every result comes from a standard acoustics formula with the speed of sound set to 343 m/s (air at 20 °C).
- Axial room modes: f = n × c / (2 × L) for each room dimension L. These modes generally carry the most energy.
- Sabine reverberation time: RT60 = 0.161 × V / A, where V is the volume in m³ and A is the sum of each surface area times its absorption coefficient.
- Eyring reverberation time: RT60 = −0.161 × V / (S × ln(1 − ā)). It is shown next to Sabine because it is more valid in small rooms with a lot of absorption.
- Schroeder frequency: about 2000 × √(T / V). Above it, modes overlap and stop behaving as separate peaks.
- Speaker boundary interference (SBIR): the first cancellation falls at f = c / (4 × d), where d is the front-wall distance.
Worked example: a 5 × 4 × 2.5 m room with drywall walls and ceiling and heavy carpet on concrete. The modes below come from the formula above. The RT60 values are the calculator’s Sabine estimates for this room.
| Quantity | Calculation | Result |
|---|---|---|
| Length mode, n = 1 | 343 / (2 × 5) | 34.3 Hz |
| Width mode, n = 1 | 343 / (2 × 4) | 42.9 Hz |
| Height mode, n = 1 | 343 / (2 × 2.5) | 68.6 Hz |
| RT60 at 500 Hz (Sabine) | 0.161 × 50 / 6.25 | 1.29 s |
| SBIR null, d = 0.4 m | 343 / (4 × 0.4) | 214.4 Hz |
The panel count works from the 500 Hz band. The calculator takes the absorption needed to reach the EBU Tech 3276 guide value 0.25 × (V/100)^(1/3) seconds, subtracts what the room already has, and divides by what one panel adds over the wall it covers. The count is capped at the available wall area.
The badge compares the mean of the 250 Hz–4 kHz octave bands with 0.4 s. That mean is an approximation: it is not the EBU Tm, which averages one-third-octave bands from 200 Hz to 4 kHz, and it does not by itself prove a room is suitable for mixing.
Porous panels absorb far less at 125 Hz than at 500 Hz. Expect the low bands to stay longer even after treatment; that is what corner bass traps are for.
Using it as a studio monitor placement calculator
Genelec and EBU Tech 3276 both specify a 60° angle between the monitors, which makes an equilateral triangle with the listener. Monitor spacing therefore equals the listening distance, and each monitor is toed in 30° so it points at your ears.
For the listening position, the calculator follows Genelec’s guidance:
- sit in the front third of the room, on the left-right center line;
- stay at least 1 m from the walls;
- avoid the exact center of the room.
The tool puts your head at one third of the room length and sizes the triangle from your monitor-to-wall distance. In a long, narrow room that triangle can end up wider than the room. The tool then hides the placement coordinates and the plan, and tells you the smallest front-wall distance that makes the triangle fit while the monitors stay in front of the listener; the alternative is a listener position closer to the front wall.
Tweeters go at ear height, about 1.2 m seated per EBU. Genelec also advises against placing monitors at exactly half the ceiling height.
There are two valid strategies for the wall behind the monitors:
- Close to the wall: Genelec prefers the monitor front less than 0.6 m (2 ft) from the wall. This pushes the SBIR null higher, where absorption behind the monitors can handle it.
- Free-standing: EBU reference rooms place monitors at least 1 m from walls, which moves the null lower.
Distances between those two ranges put the null in the low mids, so the tool suggests moving closer or farther. Rear port clearance is a separate check: Genelec asks for at least 50 mm between the port and the wall, measured from the back of the cabinet. The calculator cannot verify that from the front-baffle distance because it does not know your cabinet depth.
First-reflection points use the mirror rule: sound leaves the wall at the same angle it arrives. The tool gives the distance from the front wall to the side-wall and ceiling spots where your first panels should go.
Methodology & sources
The model assumes an empty rectangular room with uniform finishes. Air absorption is ignored, as is usual for small rooms.
Absorption coefficients are generic published values, not specific products. The same material can measure differently depending on construction; drywall at 125 Hz is one example, which is why both drywall variants are offered. Panel coefficients assume the mounting used in the published data; both rock-wool options were measured direct to masonry, which may differ from mounting them over the wall finish you select.
Some rules of thumb are deliberately left out because we found no standard or manufacturer source for them: the “38% rule” for listening position, and preferred room-ratio charts. The room-ratio warning uses only the EBU rule of avoiding ratios within ±5% of a whole number, always dividing the larger dimension by the smaller one.
- Wikipedia – Speed of sound (343 m/s at 20 °C)
- Wikipedia – Foot (unit) (1 ft = 0.3048 m)
- Wikipedia – Room modes (mode and Schroeder formulas)
- Wikipedia – Reverberation (Sabine and Eyring)
- sengpielaudio – RT60 calculator (Sabine constants)
- HyperPhysics – Absorption coefficients (Hall, Table 15.1)
- akustik.ua – Absorption coefficients (PDF) (porous absorbers)
- EBU Tech 3276 (RT60 target, ratios, 60° base angle, ear height)
- Genelec – Monitor placement
- Genelec – Improving room acoustics
Last updated: October 2026
FAQ
How many acoustic panels does my room need?
The calculator finds how much absorption brings the 500 Hz Sabine RT60 down to the EBU Tech 3276 guide value 0.25·(V/100)^(1/3) s, then divides the shortfall by what one panel adds. The result is an estimate. Sabine tends to overestimate RT60 in heavily absorbed rooms, so check the Eyring column too.
What is a good reverberation time for a home studio?
EBU Tech 3276 sets 0.2–0.4 s for reference control rooms of at least 30 m² floor area, with a guide value of 0.25·(V/100 m³)^(1/3) s. For smaller rooms, treat that formula value as a reference point, not a strict target.
How far should studio monitors be from the wall?
Genelec recommends keeping the front of the monitor preferably less than 0.6 m (2 ft) from the wall; separately, a rear port needs at least 50 mm of clearance, measured from the back of the cabinet to the wall. EBU Tech 3276 instead places free-standing monitors at least 1 m from walls. The first SBIR cancellation falls at f = c/(4·d).
What toe-in angle should studio monitors have?
In the 60° equilateral-triangle layout recommended by Genelec and EBU Tech 3276, each monitor is aimed at the listener. That works out to 30° of toe-in from straight ahead.
Why does the tool not use the 38% rule?
We found the 38% listening-position rule only on non-authoritative blogs, not in a standard or manufacturer guide. The tool uses Genelec’s guidance instead: sit in the front third of the room, at least 1 m from walls and away from the exact centre.
Related guides
- Home Studio Layout Ideas for Small Rooms, Bedrooms and Closets
- How to Acoustically Treat a Room for Recording on a Home-Studio Budget
- Acoustic Diffuser vs Absorber: Which Treatment Does Your Room Need?
- Home Studio Maintenance Checklist: Weekly, Monthly and Yearly Tasks
- Soundproofing vs Acoustic Treatment: What’s the Difference and Which Do You Need?
- How Many Bass Traps Do I Need for a Small Home Studio?
More free tools
Audio Interface Buffer Size & Latency Calculator
Convert audio interface buffer size and sample rate to milliseconds, estimate round-trip delay with your own overhead, and view a latency chart.
Headphone Drive Check: Will My Interface Power These?
Estimate whether an audio interface can drive your headphones: power in mW, maximum SPL and margin to your own target, with every step shown.
Recording Software Finder: Free & Paid DAWs and Recording Apps
Filter 23 verified recording apps and DAWs by price, license, platform, use case and feature, plus free DAWs bundled with interfaces.
