Sustain Pedal Compatibility Chart: Polarity and Brand-by-Brand Fit

You can’t judge sustain-pedal compatibility by plug size alone. Match your keyboard’s exact model, sustain-input wiring, resting polarity, and startup procedure.
Yamaha FC4A, M-Audio SP-2, and Casio SP-3 are on/off pedals; flip the SP-2 switch or restart released if response is reversed. Roland FP-30X supports DP-10 when configured correctly.
Half-damping needs a compatible continuous input, resistance range, and usually TRS wiring. Brand-specific checks below help prevent incorrect sustain and identify supported pedal functions clearly.
Polarity Switch Location Guide
To find a sustain pedal’s polarity switch, inspect the underside and side panels, since manufacturers place it differently by model.
On the M-Audio SP-2, you’ll find the polarity toggle on the pedal’s bottom panel. If your keyboard sustains notes when you release the pedal instead of when you press it, flip the toggle and retest. Correct operation means notes sustain only while you hold the pedal down.
Don’t assume every universal-style pedal includes this control: some chassis designs omit it entirely. When no switch is visible, consult the pedal’s manual or specification sheet to confirm its hardware. Then check your keyboard documentation for a polarity setting or its reversal procedure. This method prevents misdiagnosing an inverted control response as a cable or pedal failure.
Yamaha FC4A Polarity Compatibility
The Yamaha FC4A is a simple on/off sustain pedal, so it doesn’t support half-pedaling; its resting polarity must match your keyboard’s sustain-pedal input for normal operation. On compatible Yamaha instruments, you should plug in the FC4A before switching the keyboard on.
Some models read pedal status during startup, so don’t press the pedal until boot-up finishes. If sustain responds backward, consult your keyboard’s polarity setting or its startup procedure, because Yamaha’s adjustment steps differ by model.
| Keyboard family | Check | Guidance |
|---|---|---|
| Yamaha models | Startup detection | Connect first |
| MONTAGE/MONTAGE M | Manual list | Confirm fit |
| Other Yamaha models | Model-specific setup | Follow documentation |
That verification matters most with MONTAGE and MONTAGE M: use the Owner’s Manual recommended-pedal list, rather than assuming every Yamaha sustain jack accepts the FC4A.
Normally Open vs Normally Closed
Normally open (NO) and normally closed (NC) describe a sustain pedal’s electrical state while it rests: an NO pedal leaves the circuit open until you press it, while an NC pedal keeps it closed and opens it when pressed. Your keyboard must interpret that resting state correctly; otherwise, sustain can invert, latch on continuously, or fail entirely. A pedal with an open/close selector lets you correct a mismatch at the instrument. Many Studiologic instruments default to NO operation, so choose a switchable pedal when uncertain.
On Numa Compact 2, 2x, SE, and X SE models, you can set polarity in Global settings. Numa X Piano and SL models instead detect polarity at startup, so connect it before startup and don’t touch it during detection.
6.35 Mm TS Plug Types
You’ll commonly find a 6.35 mm (¼-inch) TS plug on sustain pedals, using tip and sleeve contacts only. However, you must match your instrument’s required normally open or normally closed polarity and confirm that the pedal uses a momentary, not latching, switch design. Check the Sustain or Damper jack documentation, as brands such as Studiologic may specify polarity, wiring, or 0–10 kΩ requirements for other pedal types.
Standard 6.35 Mm TS Plugs
Although 6.35 mm (¼-inch) TS plugs appear on many Yamaha, Roland, Korg, Casio, and Nord sustain pedals, matching the connector size alone doesn’t guarantee correct operation. You must also verify the pedal’s tip-and-sleeve wiring and resting polarity against your keyboard’s sustain input specification. A 6.35 mm TS connector supplies a two-conductor switch connection, but it doesn’t identify the pedal’s electrical behavior.
If you’re adapting a 5 mm TS pedal, use an appropriate adapter; the smaller plug won’t directly fit a quarter-inch jack. For basic on/off sustain, a polarity switch can correct reversed response. If you need half-pedaling, confirm that the pedal’s resistance range matches the instrument’s continuous-control requirements. This matters particularly when comparing branded pedals across otherwise similar-looking digital pianos, workstations, and stage keyboards.
Normally Open Switches
A 5 mm TS sustain pedal with a normally open switch leaves the tip-to-sleeve circuit disconnected at rest and closes it when you press the pedal. This arrangement sends the keyboard a contact-closure signal only during pedal travel. Your instrument must recognize that resting state; if it expects the opposite logic, it may sustain continuously or not respond when you play. Don’t assume a 5 mm TS plug guarantees a match.
Confirm the pedal’s internal wiring, connector size, and the sustain input specification in your keyboard’s manual. Many universal pedals include a polarity switch, letting you select the resting behavior your model requires. Check the documentation for Yamaha, Casio, Roland, Korg, or other brands before connecting, because manufacturers don’t follow one shared polarity standard.
Normally Closed Switches
Normally closed 5 mm TS sustain pedals keep the tip-to-sleeve circuit connected while at rest and open it when you press the pedal. Your keyboard must support this closed-at-rest polarity; otherwise, sustain may work backward or stay engaged. Don’t assume the 5 mm TS plug determines compatibility: it describes connector format, while the instrument’s sustain jack wiring and polarity requirement determine operation. Check the pedal’s open/close selector, then confirm the keyboard setting or manual.
On Studiologic Numa Compact 2, 2x, SE, and X SE models, select sustain-pedal polarity in Global settings. With Numa X Piano and SL instruments, connect the pedal before restarting, because they identify polarity at startup. Studiologic commonly defaults to open-at-rest pedals, so a selectable-polarity pedal gives you the safest fit.
Latching Versus Momentary Designs
Switch behavior—not the 5 mm TS connector—determines whether a pedal works as a sustain control. A TS plug supplies only tip and sleeve; it doesn’t identify switch mechanism or resting wiring. Your keyboard needs a momentary pedal: pressing it changes the circuit, and releasing it returns it to its rest state. A latching footswitch remains changed after release, making it generally unsuitable for piano-style sustain input.
Before connecting, check each manufacturer’s manual for momentary versus latching operation, normally open or normally closed rest state, and wiring details. If sustain activates on release instead of press, states don’t match. Use a pedal or keyboard polarity control to correct operation. Don’t assume a TS-equipped accessory is automatically a sustain pedal. Confirm all specifications before you connect.
Brand-Specific Polarity Needs
Brand conventions matter because a 5 mm TS plug doesn’t define the pedal’s resting polarity or wiring. When you match a Yamaha keyboard, verify its expected on/off polarity; a switchable pedal such as the M-Audio SP-2 lets you reverse it when needed. Don’t treat that switch as a half-pedal solution: Yamaha half-pedaling requires a continuous pedal with the correct resistance range, not a standard on/off SP-2.
Studiologic instruments generally require a sustain pedal that’s open at rest, although some models let you change polarity in Global settings. On Numa X Piano and SL models, connect the pedal before you restart the instrument; they detect sustain-pedal polarity during startup. Check both polarity and wiring before you buy or troubleshoot a 5 mm TS pedal connection.
Match Model Numbers First
Start by matching your keyboard’s exact model number to the pedal’s exact model and connector specification, because sustain compatibility can change across closely related product lines.
On Studiologic Numa Compact 2/2x/SE/X SE, set sustain-pedal polarity in Global settings. Numa X Piano and SL detect polarity at startup, so connect the pedal before restarting.
Map Studiologic pedals by their designated inputs: VP/25 works only at PED4, and you must select it in the zone’s PED4 settings; VP/27 and FP/50 fit PED3.
For Yamaha MONTAGE/MONTAGE M, consult the Owner’s Manual for recommended pedal models. An M-Audio SP-2 must use Yamaha-compatible on/off polarity. Check both the instrument’s input specification and the pedal’s wiring before buying; a matching plug alone doesn’t guarantee operation on that specific keyboard model.
Half-Damper Needs TRS Jack
Half-damper control requires more than a plug that fits: your keyboard must support continuous sustain input, and the pedal must match its specified wiring and resistance range. Unlike a switch pedal, a half-damper sends graduated values, commonly 0 to 127, so you can vary decay rather than choose only fully off or fully on.
You’ll usually see a TRS input for this function, but don’t treat TRS as a universal standard. Yamaha, Kawai, Casio, and other brands may specify different resistor behavior or tip/ring assignments. Check your instrument manual for an explicitly labeled half-damper or continuous-damper input, then compare its required resistance range and wiring diagram with the pedal documentation. A basic TS on/off pedal can physically connect through adapters yet still deliver no intermediate sustain.
Roland FP-30X With DP-10
The Roland DP-10 works with the FP-30X as a piano-style sustain pedal and can provide half-pedaling when you use the piano’s compatible pedal input and correct configuration. Before relying on it, verify the jack assignment, connection method, and supported functions in Roland’s FP-30X and DP-10 documentation.
Set the DP-10’s side switch to the polarity mode the FP-30X requires. An incorrect setting may reverse sustain behavior, so notes hold when you release the pedal, or prevent normal operation altogether. Unlike a basic switch-only footswitch, the DP-10 can transmit variable pedal position for compatible half-pedal response. If you get reversed, inconsistent, or missing sustain, inspect the switch position and FP-30X pedal settings. After you alter a cable connection or setting, restart the piano and test full pedal travel.
Power-On Pedal Detection
Because some keyboards read sustain-pedal polarity during startup, the pedal’s resting position at power-on can determine whether sustain works normally or in reverse. Before you play, connect the pedal and let it rest fully released. Yamaha models that support startup detection should boot with the pedal up; if sustain is reversed, power off, release it, and restart.
Numa X Piano and SL units also identify polarity at startup, so reconnect the pedal before restarting. This procedure matters when a normally closed or normally open pedal doesn’t match the instrument.
- Yamaha: start with pedal released.
- Numa X Piano and SL: connect first, restart.
- Check the pedal’s polarity switch.
- Follow the keyboard’s specified startup procedure.
- Test pedal and keyboard separately if reversal persists; either may be faulty.
Casio SP-3 Pedal Fit
Casio’s SP-3 can work as a basic sustain pedal if your keyboard provides a compatible sustain or damper input, but you should verify the exact model’s specifications before connecting it. Confirm that your Casio has a compatible sustain or damper jack; connector presence alone doesn’t guarantee expected operation. Polarity matters: a mismatch can make notes sustain when you release the SP-3 or prevent sustain when you press it.
- Check the keyboard manual for supported pedal type.
- Try its polarity setting, if the model includes one.
- Follow the specified startup procedure for polarity detection.
- Don’t expect half-pedaling; SP-3 supplies only on/off switching.
- If results remain unclear, test pedal and keyboard separately.
Consult both manuals before performance use.
Conclusion
You’ll avoid most sustain-pedal failures by matching the piano’s specified model, plug type, and switch polarity before you buy. Check whether your Yamaha, Roland, Casio, Korg, or Nord expects normally open or normally closed operation, and confirm whether it supports TS switching or TRS half-damper data. Use the pedal’s polarity switch, then reconnect or power-cycle the keyboard so it detects the correct state. For Roland FP-30X, choose DP-10 compatibility deliberately rather than assuming universal fit.






